Logo

B1311 Engine Trouble Code

B1311 Engine

When you check engine light came on code B1311 the reason should be . However your vehicle's manufacturer may have a different definition for the B1311 OBD-II Diagnostic Body (B) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes B1311 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

B1311 Code Meaning :

B
OBD-II Diagnostic Body (B) Trouble Code For Engine
1
Fuel And Air Metering
3
Fuel Rail Pressure Sensor Circuit Malfunction
1
Ignition/Distributor Engine Speed Input Circuit Malfunction
1
Glow Plug/Heater Circuit 'A' Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

B1311 OBD-II Diagnostic Body (B) Trouble Code Description

B1311 engine trouble code is about Glow Plug/Heater Circuit 'A' Malfunction. Fuel Rail Pressure Sensor Circuit Malfunction and Ignition/Distributor Engine Speed Input Circuit Malfunction causes most of code B1311.

Reason For B1311 Code

The reason of B1311 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

B1311 DTCs may also be triggered by engine faults earlier down the line. For example, a dirty MAF sensor might be causing the car to overcompensate in its fuel-trim adjustments. As a result, oxygen sensors are likely to report fuel mixture problems.

How To Repair B1311 Code

Before starting let's see B1311 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access B1311 code stored in the ECU.
  • Technicians will note B1311 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A knocking sound that comes out of your bonnet is a definitive sign of an engine that is failing. Engine damage wear can cause this sound in your engine's technical components such as pistons, bearings or other motioning components.Some recurrent solutions for this situation might be in replacing the spark plugs, testing and replacing your ignition coils.

If nothing is done to repair the persistent B1311 code, the ECU will put the vehicle into a limp mode. This mode limits the top speed and reduces engine power greatly to protect the engine.

Sometimes B1311 code comes with B131100 code.

Diagnosis Of Engine Error OBD Code B1311

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a B1311 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the B1311 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.